Step 1:
Prefold over this line.

Step 2:
Make a valley-fold over these 2 lines.

Step 3:
Make a valley-fold over these 2 lines.
                                                            

Step 4:
Unfold the model.
                                                            

Step 5:
Make a mountain-fold over the line at the right and a valley-fold over the line at the left.
                                                            

Step 6:
Make a valley-fold over the line at the right and a mountain-fold over the line at the left.
                                                            

Step 7:
This is the other side of the model.
                                                            

Step 8:
Make a square shaped tube by rolling the model up over these prefolded lines.
                                                            

Step 9:
Here a part of the folds from step 8 is already done.
                                                            

Step 10:
Hold the model the same as I do here. Press the model inwards by making a valley-fold over the black line. Do the same on the backside. Then press the model flat from above and below, see large arrows. Don't press the end on the left and right flat. The 2 small arrows show that the upper corner lays over the other corner.

Step 11:
Repeat step 10 on the other side.
                                                   
                                                            

Step 12:
Now the model looks like this.
                                                   
                                                            

Step 13:
Press the model inwards by making a valley-fold over the line in the middle and a mountain-fold over the 2 outer lines. Make the same folds on the other 3 sides of the square tube.

Step 14:
Make a valley-fold over this line. Make the same fold on the other 3 flaps of the torch.

Step 15:
Hold the tip of the torch in one hand, see arrow at the left. Then twist it counter clockwise a little, see curved arrow.

Step 16:
This part is done

Step 17:
The book is folded on the other end.

Step 18:
Make this part of the model flat by folding over these two lines (mountain-fold).

Step 19:
Make a mountain-fold over the line at the right and a valley-fold over the line at the left.

Step 20:
Turn the model

Step 21:
Make a valley-fold over the black line. This line is just below the arrow. The corner indicated by the arrow is pulled upwards when you make this fold.

Step 22:
The arrow shows the corner of step 21. Press the place indicated by the arrow flat from above.

Step 23:
Repeat step 21 and 22 at the other side, see black line

Step 24:
Turn the model

Step 25:
Make a valley-fold over this short line.

Step 26:
This piece is done....

Step 27:
This dollar bill is for the body of the model. Make a valley-fold over this line, it's a little above the center-line.

Step 28:
Fold the model in half over this line.

Step 29:
Make a valley-fold over this line. Make the same fold at the backside of the model.

Step 30:
Make this fold over the upper layer only. Do the same on the other side of the model.

Step 31:
Now this piece can be placed straight up.

Step 32:
Done too.....

Step 33:
This note is for the head. Make a valley-fold over these 2 lines.

Step 34:
Make a valley-fold over these 2 lines.

Step 35:
Now you've made a square piece of paper actually. Prefold the model over these 4 lines.

Step 36:
First, make a valley-fold over the 2 lines at the bottom right. Then make a mountain-fold over the 2 lines in the middle. And make a valley-fold over the 2 lines at the top left.

Step 37:
Fold the flap below the black line upwards by making a valley-fold over the black line. Make the same fold at the backside.

Step 38:
Bookfold the flap on the right to the left over this line. Make the same fold at the backside.

Step 39:
Fold the flap below the black line upwards. Do the same at the backside.

Step 40:
Make an inside reverse fold over these 3 lines. Do this by making a mountain-fold over the line in the middle and a valley-fold over the 2 outer lines. The 2 ends indicated by the small arrows are pulled towards each other while you make these folds.

Step 41:
Repeat step 40 on the other 3 same places of the model, see arrows.

Step 42:
Pull the 2 ends indicated by the arrows upwards, out of the model. These 2 pieces will keep the head steady on the body later.

Step 43:
Press the pieces from step 42 flat between your fingers, see arrows.

Step 44:
And the head is done too....

Step 45:
This note is for the base of the model. Prefold the paper over this line.

Step 46:
Prefold over these 2 lines.

Step 47:
Prefold over this line

Step 48:
And prefold over this line. Use the lines of step 45 and 47 as guidance.

Step 49:
Unfold

Step 50:
Prefold over these 2 lines. Use the points where the lines of step 46 and 48 cross as guidance.

Step 51:
Make an inside reverse fold over these 3 black lines. The 2 lines at the right are already prefolded. The black line in the middle is a mountain-fold and the other 2 lines are valley-folds. You almost automatically make a valley-fold over the 2 red lines while you are making these folds.

Step 52:
Repeat step 51 over these 3 black lines.

Step 53:
Repeat step 51 and 52 over these lines

Step 54:
Turn the model

Step 55:
Make a mountain-fold over the short line above the arrow at the left. Make the same fold on the other side of the model, see arrow at the right.

Step 56:
And the base is done too...

Step 57:
Slide the piece on the right in the body, see arrows

Step 58:
Make a mountain-fold over these 2 lines. Fold over all paper layers in once. Now the arms are locked.

Step 59:
Place the body on the base

Step 60:
Place the head on the body. The center of the head (see small arrow) is placed in front of the neck. And the two ends indicated by the large arrows are placed behind the neck. (This are the ends of step 43) If necessary, you can use the arm for extra balance.