Step
1:
The other side of this origami paper is
white,
turn the paper.
Step
2:
Prefold over these 4 lines
Step
3:
First valley-fold over the 2 lines
below, on the right.
Then
mountain-fold over the 2 diagonal lines in the
middle.
And valley-fold over the 2 lines at the top left.
Step
4:
Pull the flap upwards
Step
5:
Squash fold the flap
Step
6:
Valley-fold over these 2 lines
Step
7:
Unfold the folds of step 6
Step
8:
Pull the edge indicated by the arrow
downwards
by making
a valley-fold over the purple line
Step
9:
Press the edges indicated by the arrows
downwards
Step
10:
Valley-fold the triangular flap upwards
Step
11:
Repeat steps 5 to 10 on the other 3
flaps,
see arrows
Step
12:
Pull the ends outwards, in the direction
of
the
arrows.
Step
13:
Mountain-fold the triangular flap to the
inside
of the
model
Step
14:
Push the
2 ends towards each other again
Step
15:
Repeat
steps 12 to 14 on the other 3 same places
of the model
Step
16:
Bookfold
one edge to the right.
Do the same on the backside
Step
17:
Valley-fold the flap downwards
Step
18:
Turn and
rotate the model 180 degrees
Step
19:
Bookfold
2 edges to the left
Step
20:
Valley-fold this flap straight upwards
Step
21:
The flap
stands straight up now.
Fold the
2 edges of step 19 back to the right
and push/press/fold the flap flat while
you do this
Step
22:
Repeat
steps 19 to 21 on the left,
mirror-wise
Step
23:
Mountain-fold over these 2 purple lines.
Then,
turn the model
Step
24:
Valley-fold over these 2 purple lines.
Step
25:
Turn the model again
Step
26:
Fold over these 3 purple lines.
Step
27:
Now the model looks like this
Step
28:
Press the tail flat by making a
mountain-fold over
this purple line.
Step
29:
Open the tip of the tail wing with your
fingers,
then press it flat between your fingers
Step
30:
Mountain-fold over this short purple line
Step
31:
And now the model looks like this
Step
32:
Press the tail flat from aside, see
arrows.
Use the 2 inside reverse folds as help
Step
33:
Press/fold/bend the tail wing downwards
on the spot
indicated
by the upper arrow. And press/fold/bend it
upwards at the
spot indicated by the arrow below.
Step
34:
Mountain-fold the wings downwards a
little
Step
35:
Make an outside reverse fold over these
lines
(=valley-fold over these 2 lines and a mountain-fold
on the other side of the head at the
same spot as
the short line on the left)
Step
36:
Press 2 edges downwards, see arrow.
Do the same on the other side of the head
Step
37:
Press the head flat from aside, see
arrows
Step
38:
Valley-fold over this short purple line
Step
39:
Now the head looks like this
Step
40:
This is the model viewed from below.
Valley-fold the corner indicated by the arrow
upwards a little.
Step
41:
Pull the corner further upwards by
folding over
these 3
purple lines (=mountain-fold over the line
in the
middle and valley-fold over the 2 outer lines)
Step
42:
Press the edge indicated by the arrow
inwards by
making an inside reverse fold over these
3 lines
(=mountain-fold over the short line in the middle
and valley-fold over the 2 outer lines)
Step
43:
Repeat steps 40 to 42 on the corner at
the left,
see arrow
Step
44:
Turn the model
DONE!
This is a video with instructions for folding
the Dimorphodon-Dino: