Step
1:
The other side of this paper is black.
Prefold over these 4 lines
Step
2:
First valley-fold over the 2 lines at the bottom-right.
Then mountain-fold over the 2 diagonal lines in the
middle. And valley-fold over the 2 lines at the top-left.
Step
3:
Fold the flap indicated by the arrow upwards
Step
4:
Squash-fold the flap
Step
5:
Valley-fold over these 2 lines
Step
6:
Unfold the folds of step 5
Step
7:
Pull the edge indicated by the arrow downwards
by making a valley-fold over the red line
Step
8:
Press the edges flat, see arrows
Step
9:
Valley-fold the triangular flap upwards
Step
10:
Pull the 2 ends outwards, in the direction of
the arrows
Step
11:
Mountain-fold the triangular flap to the inside of
the model
Step
12:
Push the 2 ends towards each other again,
see arrows
Step
13:
Repeat steps 4 to 12 on the other 3 flaps
Step
14:
Bookfold one layer to the right.
Then rotate the model, see next picture
Step
15:
Valley-fold over these 2 lines
Step
16:
Bookfold one layer to the right
Step
17:
Repeat step 15 on the other side, see arrow
Step
18:
Open the model, see arrow
Step
19:
Valley-fold the flap upwards
Step
20:
Press the model flat again, see arrows
Step
21:
Repeat steps 19 and 20 on the other side,
see arrows
Step
22:
First mountain-fold over the upper line,
then over the line below
Step
23:
Pull the tip indicated by the arrow upwards by making
an inside reverse fold over these lines.
Do the same on the other leg
Step
24:
Press the leg flat from aside by making
a mountain-fold over the red line.
Do the same on the other leg
Step
25:
Rotate the leg counter-clockwise, see arrow.
Rotate the other leg clockwise
Step
26:
Valley-fold over these 2 lines
Step
27:
Push the edge indicated by the arrow inwards by
making an inside reverse fold over these 3 lines
(=valley-fold over the short line in the middle and
mountain-fold over the 2 longer lines)
Step
28:
The headless man is done.....
Step
29:
This paper is for the horse, the other side is grey.
Prefold over these 4 lines.
Step
30:
First valley-fold over the 2 lines at the bottom-right.
Then mountain-fold over the 2 diagonal lines in the
middle. And valley-fold over the 2 lines at the top-left.
Step
31:
Fold the flap on the right of the red line upwards
Step
32:
Squash-fold the flap
Step
33:
Valley-fold over these 2 lines
Step
34:
Unfold the folds of step 33
Step
35:
Pull the edge indicated by the arrow downwards
by making a valley-fold over the red line.
Step
36:
Press the edges flat/downwards
Step
37:
Valley-fold the triangular flap upwards
Step
38:
Pull the 2 ends outwards, in the direction of
the arrows.
Step
39:
Mountain-fold the triangular flap to the inside
of the model
Step
40:
Push the 2 ends of step 38 towards each other
again, see arrows.
Step
41:
Repeat steps 32 to 37 on the other 3 flaps.
And repeat steps 38 to 40 on 2 of the 3 other flaps.
Step
42:
Turn the model, with the small triangular flap
on top, see next picture
Step
43:
Valley-fold the edge indicated by the arrow
upwards.
Step
44:
Make an inside reverse fold over these 3 red lines.
Then push the edges between the arrows towards
each other again.
Step
45:
Mountain-fold the edge below the red line to the inside
of the model.
Make the same fold (=valley-fold) on the layer below,
see arrow
Step
46:
Pull the tip indicated by the arrow to the inside of the
model by making an inside reverse fold over these lines.
Step
47:
Repeat steps 44 to 46 on the flap indicated by
the arrow
Step
48:
Valley-fold over these 2 lines.
The pieces indicated by the 2 arrows are of
the same length
Step
49:
Mountain-fold the model in half
Step
50:
Make an inside reverse fold over these lines.
The 2 places between the arrows are of the
same length.
Step
51:
And make an inside reverse fold over these lines.
DONE! hope he knows
where he's going...
And this is a video with me folding the headless man with horse with
head: